CODE ALARM

Installation manual

System Layout

. 1

System Specifications

System Arming

The system will ignore all trigger inputs for 25 seconds after the second arming chirp / light flash

Alarm Trip Cycle

Siren will sound for 30 seconds The alarm will then ignore all trigger inputs for 10 seconds, then rearm The siren will not sound again until another intrusion is detected

Panic

Pressing any two buttons on the remote transmitter activates the Panic feature Panic duration is 30 seconds Pressing any button on the remote transmitter de-activates the Panic feature

Sensors
Automatic Arming

If the Automatic Arming option is enabled, the alarm will automatically arm and disable the vehicle starter 20 seconds after the ignition is turned off and the last door is closed, or 2 minutes after the alarm is disarmed and not manually re-armed

Automatic Immobilization

If the Automatic Arming option is not enabled, the alarm will automatically disable the vehicle starter 20 seconds after the ignition is turned off and a door is opened, or 2 minutes after the alarm is disarmed and not re-armed.

Valet
Illuminated Entry

The Illuminated Entry Output is activated for 60 seconds after the alarm is disarmed.

Trunk Release / Auxiliary Output

The Trunk Release / Auxiliary Output is activated by pressing and holding DISARM or ARM (selectable) on the remote transmitter The output duration lasts as long as the button is held (up to 45 seconds).

Door Locks
Trip Identification
# of Chirps Zone
1 Sensor 1
2 Sensor 2
3 Door, Hood, Trunk
4 Ignition
Auxiliary Output 1

Auxiliary Output 1 is activated at any time by pressing OPTION 1 on the remote transmitter. The output is activated as soon as the button is pressed, and will continue to operate for a preset time. The preset time duration is programmable to .6, 6, 12, or 24 seconds.

Note: Pressing the OPTION 2 button while Auxiliary Output 1 is active will turn off Auxiliary Output 1.

Auxiliary Output 2

Auxiliary Output 2 is activated at any time by pressing OPTION 2 on the remote transmitter. The output is activated as soon as the button is pressed, and will continue to operate for a preset time. The preset time duration is programmable to .6, 6, 12, or 24 seconds.

Note: Pressing the OPTION 1 button while Auxiliary Output 2 is active will turn off Auxiliary Output 2.

Installation

Remove all fuses from the wire harness before installation.

A. Siren (#20 ORANGE)
B. 12V+ Main Feed (#22 RED)
C. 12V+ Switched Feed (#17 Lt. BLUE)

* If you are connecting the optional 2-Cut immobilizer, make sure to connect the #17 Lt. BLUE wire closest to the ignition switch. See page 12 for further details.

D. Ground (#11 BLACK)
E. Starter Interrupt (WHITE/RED and WHITE on 2-pin Connector)

Note: Some vehicles have two starter wires. If so, cut both and connect to the alarm module. Refer to Vehicle Wire Color and Location Chart.

F. Door Pin Switches (#8 YELLOW or #19 WHITE)
Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline:
G. Illuminated Entry (#4 YELLOW and #3 YELLOW/BLACK)
H. Parking Lights (#2 ORANGE/BLACK and #1 BLACK/WHITE)
I. Hood /Trunk Pin Switch (#7 Lt. GREEN)
J. Power Door Locks: #14 Lt. BLUE, #13 Lt. BLUE/BLACK, #10 RED/BLACK, #6 RED/WHITE, #16 GREEN, #15 GREEN/BLACK
Type 1 - Positive 3-Wire Door Lock System
Type 3 - Negative 3-Wire Door Lock System
. 2
Type 2 - Positive 5-Wire Door Lock System
. 3
Type 4 - Vacuum Door Lock System
. 4
K. Status Indicator (#18 GRAY)
L. Trunk Release / Aux. Output (#5 VIOLET and #12 TAN)

Note: This output can be programmed to act as a trunk release output or auxiliary output (See Programming Selectable Options - next page )

* lf connecting to a negative trunk release system a specific connection location may be required Refer to Vehicle Wire Color and Location Chart

M. Auxiliary Outputs 1 and 2 (#21 PINK and #9 BLACK/GREEN)
. 5
N. Impact Detector
O. Armed Output (BLACK on Sensor Port 2)

System Power-Up

Programming Selectable Options

  1. Make sure the system is disarmed and the ignition is off
  2. Without starting the vehicle turn the ignition ON, OFF, ON, OFF, then ON, at 1/2-second intervals

    After two (2) seconds the status indicator will begin flashing for Code Entry. Follow the Code Entry Procedure If the correct code is entered the siren will chirp three times indicating entry into the Selectable Options Mode.

  3. Press Button 1 on a programmed remote transmitter to begin option selections
. 6
Option Number and Description     Bold Type Indicates Factory Settings Status Indicator ON Status Indicator OFF
1 Doors lock when all doors are closed and vehicle ignition is turned on YES NO
2 Doors unlock when vehicle ignition is turned off YES NO
3 Lock / Unlock Output Duration 6 sec 1/2 sec
4 Trunk/Aux Output is Activated by Pressing and Holding ARM or DISARM ARM DISARM
5 Siren chirps when arming and disarming YES NO
6 System arms automatically 20 seconds after last door is closed YES NO
7 Auxiliary Output 1 Timer Programming See Timer Programming Section Below
8 Auxiliary Output 2 Timer Programming

Timer Programming

Auxiliary Outputs 1 and 2 can be programmed to send a specific timed output when their respective buttons are pressed.

When programming Option number 7 or 8, the LED will flash a number of times, indicating the current timed output setting.

# of Flashes Output Duration
1 0,6 seconds
2 6 seconds
3 12 seconds
4 24 seconds

Pressing DISARM on a programmed transmitter advances to the next option.

To Exit Selectable Options Mode, turn the vehicle ignition On, then Off.

Testing the Alarm System

1. Arming and Disarming / Sensor Override
Close all doors and press ARM
  • All doors lock
  • Siren chirps two times / parking lights flash two times
  • Status indicator turns on
Within 5 seconds press ARM again
  • Siren chirps three times (sensor override)
Press Disarm
  • All doors unlock
  • Siren Chirps once / parking lights flash
  • Status indicator turns off
  • Courtesy light turns on (if connected)
2. Alarm Triggering / Starter Interrupt /Trip ID / Lock Options
Arm system. Wait 30 seconds then open door
  • Siren sounds / parking lights flash
With siren sounding attempt to start vehicle
  • Vehicle will not start
Wait until siren stops then press DISARM
  • Siren chirps / parking lights flash 4 times (System was triggered)
Press DISARM again
  • Siren chirps three times (System was triggered by door)
Close doors and attempt to start vehicle
  • Vehicle starts
  • Doors lock (if Ignition Lock Option is activated)
Turn ignition off
  • Doors unlock (if Ignition Unlock Option is activated)
3. Trunk Release /Auxiliary Option
Press and hold ARM or DISARM (depending on options programming)
  • Trunk opens or aux device activates
4. Panic
Press two buttons for one second
  • Siren sounds / parking lights flash for 30 seconds. Press either button to stop
5. Automatic Arming (Test only if Automatic Option is activated)
Enter vehicle and close doors Turn ignition on for five seconds then turn off. Exit vehicle and close doors.
  • Alarm arms 20 seconds after door is closed
6. Valet
With system disarmed turn ignition on, then press DISARM
  • Status Indicator Flashes twice (enters Valet Mode)
Turn ignition off
  • Status indicator flashes every 1/2 second
Close all doors and press ARM
  • Flashing stops and system arms
7 Auxiliary Outputs (Test if connected)
Press OPTION 1 on the remote transmitter
  • Accessory connected to Aux. Output 1 activates
Press OPTION 2 on the remote transmitter
  • Accessory connected to Aux. Output 2 activates
Testing the Emergency Disarm Procedure
  1. Exit the vehicle close all doors and arm the alarm system Wait 30 seconds, then trigger the alarm by opening a door
  2. With the siren sounding enter the vehicle and turn the ignition to the ON position

After two (2) seconds the status indicator will begin flashing for Code Entry. Follow the Code Entry Procedure

If the correct code is entered, the alarm system will disarm.

Adjusting the Impact Detector

  1. Turn the white knob on the impact detector clockwise until it stops, then turn counter clockwise approximately 1/4 of a turn.
  2. Test the sensitivity by arming the alarm system, waiting 30 seconds then slapping various parts of the vehicle with an open hand.
  3. Adjust the sensitivity until the desired setting is achieved.
. 7

If your system includes the optional 2-Cut Immobilizer, refer now to the installation instructions. Return to this section when installation and testing of the Immobilizer are complete.

Antenna Placement /Mounting the Module

1a. If the module has a short antenna (approx 8) keep the antenna as straight as possible and route away from vehicle harnesses

1b. If the module has a long antenna completely uncoil the antenna and route up the nearest front window pillar to the headliner Be careful not to pinch the antenna under vehicle panels or route near moving parts.

2. For optimum performance allow the clear plastic portion of the antenna to remain exposed in the corner of the window or behind the rear-view mirror.

IMPORTANT!!!

Before mounting the module, write the alarm code (found on the back ol the module) in the space provided on the front of the Owner's Manual. FAILURE TO DO SO COULD CAUSE YOUR CUSTOMER TO BE STRANDED SHOULD THE REMOTE TRANSMITTER EVER FAIL!

3. Mount the module using supplied long tie wraps Make sure the module and harnesses are clear of moving vehicle parts.

Immobilizer Installation

Note: Immobilizer wires are numbered at the ends for identification. When connecting the wires, cut off the numbered sections to enhance security.

. 8
1. Code Input (BLACK/PINK)

Note: The #21 PINK wire can connect to both the Immobilizer AND an auxiliary relay.

2. Ground
3. 12V+ Switched Power

IMPOTANT! If you are using CUT 1 or CUT 2 to interrupt the vehicle ignition wire, connect the alarm module #17 Lt. BLUE and the immobilizer #3 wire closest to the ignition switch.

. 9
4. Cut 1 In/Out Wires (max. 30A)
5. Cut 2 In/Out Wires (max. 30A)
Power-Up and Testing of the Immobilizer

The immobilizer learns the code of the alarm system when it is first connected and the ignition is turned on. From this point on, the immobilizer is "matched" to that particular alarm. If the alarm module is changed, or if the immobilizer is removed and connected to a different alarm, the immobilizer will not operate (the vehicle will not start.)

  1. Make sure the alarm is disarmed.
  2. Turn the vehicle ignition to the ON position.
  3. Observe the LED on the immobilizer.
  4. Verify that the vehicle starts.

Note: The immobilizer interrupts the selected wires whenever the alarm system interrupts the starter wires. Verify that the wires are disabled under the conditions listed in the Automatic Arming and Automatic Immobilization sections of System Specifications.

Mounting the Immobilizer

Programming Remote Transmitters

Note: Each system module has four "slots", or memory locations, to store remote transmitter codes, giving it the ability to operate from up to four remote transmitters. For proper operation, a transmitter code must be stored into each memory slot. When using less than four transmitters, follow the suggested programming parameters:

  1. Make sure the system is disarmed and the ignition is off.
  2. Without starting the vehicle, turn the ignition ON, OFF, then ON, at 1/2-second intervals.

    After two (2) seconds, the status indicator will begin flashing for Code Entry. Follow the Code Entry Procedure (below). If the correct code is entered, the siren will chirp twice, indicating entry into the Transmitter Programming Mode.

  3. Wait 5 seconds. Press Button 1 on the remote transmitter to be programmed. The siren will chirp once, indicating that the system has "teamed" that transmitter.
  4. Repeat step 3 for any additional remote transmitters or transmitter codes.
  5. Exit the Transmitter Programming Mode by turning the vehicle ignition on, then off. Test all remote transmitters to ensure that they work properly.

Code Entry Procedure

  1. Enter the Code Entry Mode by following the steps in the Programming Remote Transmitters, Programming Selectable Options, or Testing the Emergency Disarm Procedure sections of this manual.

    The status indicator will begin flashing for Code Entry.

  2. Look at the first number in the code. Allow the status indicator to flash the corresponding number of times as the first number in'the code.
  3. After the status indicator has flashed the corresponding number of times, turn the vehicle ignition off. The first number has been entered.
  4. Turn the ignition back to the ON position. The status indicator will again begin flashing. Repeat the procedure in steps 2 and 3, this time using the second number in the code.
  5. Repeat steps 2 and 3 for the third and fourth numbers in the code.
  6. After the fourth number has been entered correctly, the alarm will disarm, or enter the desired programming mode.

Note: If you enter an incorrect digit, turn the vehicle ignition off, then on. When the status indicator begins to flash, re-enter the code from the beginning.

Example: The code is 2314.

  1. Enter the Code Entry mode.
  2. Allow the status indicator to flash two (2) times. After the second flash, turn the vehicle ignition off.
  3. Wait one second, then turn the ignition on.
  4. Allow the status indicator to flash three (3) times. After the third flash, turn the vehicle ignition off.
  5. Enter the third and fourth numbers in the same manner.
26.12.2001